Harman Kardon Home Theater System CP 25 User Manual

®
CP25 QUICK-START GUIDE  
Thank you for purchasing a Harman Kardon CP 25 Home Theater System.  
This Quick-Start Guide will help you with a basic system installation. For  
detailed information on any step in this Guide, please refer to the pages  
referenced in the Owner’s Manual for the AVR 235 that is part of this system.  
We strongly recommend that you read all four Owner’s Manuals for complete  
details on how to install, configure and operate the AVR 235, DVD 22, HKTS 7  
and HKS 3, as well as for the important safety information they contain. You  
should also read the Owner’s Manual for the included RCP 2 system remote.  
FRONT  
RIGHT  
SPEAKER  
CENTER  
SPEAKER  
(Green)  
FRONT  
LEFT  
SPEAKER  
(Red)  
(White)  
SURROUND  
RIGHT  
Figure 1 – Speaker Placement  
The colors shown for each speaker correspond to  
the matching output terminal connection on the back  
of the AVR 235 (see page 7).  
SPEAKER  
(Gray)  
SUBWOOFER  
(Purple)  
Connections Color Guide  
SURROUND  
Audio Connections  
Front  
Left  
Right  
LEFT  
SPEAKER  
SURROUND BACK  
RIGHT SPEAKER  
(Tan)  
Center  
Surround  
(Blue)  
SURROUND BACK  
LEFT SPEAKER  
(Brown)  
Subwoofer  
Surround Back  
Digital Audio Connections  
Coax  
Optical  
Video Connections  
Composite  
Step 1. Place your speakers in the listening room  
(see page 16).  
S-Video  
Match the colored jacks on the AVR 235 to the appropriate  
jacks on your source equipment or speakers. The colors are  
standardized, but not all equipment or connectors use them.  
SPEAKER PLACEMENT  
 
AM Antenna  
FM Antenna  
240  
Figure 4 – DVD Connections  
Dotted lines (• • • ) indicate a  
connection where more than  
one option is available. You may  
use standard composite video,  
S-video or component video, but  
you do not need to use more than  
one video type.  
Step 4. Connect AM and FM antennas (as shown above). (See page 14.)  
Step 5. Connect the DVD 22 to the AVR 235 as shown above:  
AUDIO connections: Connect the L/R Audio Out jacks on the DVD  
to the L/R DVD Audio in jacks on the AVR.  
Step 6. Connect other source devices such as a VCR, Cable or Satellite set-  
top box, HDTV receiver or audio recorder using the connections  
shown in the Device Connection Options chart and Figure 5 on the  
back of this Guide. Plug all sources into an AC power outlet.  
Step 7. Connect the AVR to your TV or video display. You must make a  
composite, S” or component video connection corresponding to  
each video source device used in your system. Remember to switch  
the TV to the correct input for each source.  
Basic Configuration  
Step 8. Select digital inputs: Use the On-Screen Input Setup menu or the  
front-panel Digital Select button and the arrow buttons to select an  
optical or coaxial digital input, for any digital source other than the  
DVD (see pages 18 and 28).  
DIGITAL AUDIO connections: Use the enclosed coaxial interconnect  
(orange connectors) to connect the Coaxial Digital Output on the  
DVD to the Coaxial Digital 1 Input on the AVR.  
VIDEO connections: Depending on the input available on your TV,  
use either composite video (dotted yellow), S-video (dotted black)  
or component video (dotted red/blue/green) connections. Only one  
connection type is needed.  
POWER: Plug the DVDs AC power cord into the SWITCHED output  
on the back of the AVR. When you have finished making all connec-  
tions, press the Main Power Switch on the DVD to turn it on (see  
pages 14–17).  
TM  
Step 9. Use  
to set output levels: Set the Balance to 12 o’clock,  
and the Volume to –10dB. Hold the remote in front of you at shoulder  
level, and point it at the AVR 235. Press the SPL button for 3 seconds,  
and release it when the LED flashes amber. Press 7” to indicate a  
6.1/7.1 system. Hold the remote steady, and wait for the process to  
be completed (see page 23).  
NOTE: The AVRs on-screen menus are not available when viewing  
a component video connection. For that reason, a composite or  
S-video connection is recommended, though not required, when  
component video is used.  
Step 10. If you are using a component video connection to a digital television,  
set the DVD 22’s output to Progressive Scan, as shown on page 20  
of the DVD 22 manual.  
Step 11. Your system is configured – sit back and enjoy!  
SPEAKER AND DVD CONNECTIONS  
 
VCR (Video 1)  
R
TV or Video Monitor  
S-Video  
Cable or Sat or HDTV Set-Top Box (Video 2)  
OUT  
L
VIDEO  
Video  
Component Video  
Component Video  
L
R
Video  
S-Video  
Y
Pb  
Pr  
Y
Pb  
Pr  
In/Rec  
IN  
Out/Play  
Optical  
Coax  
AUDIO RECORDER  
Figure 5 – Source Component Connections  
Dashed lines (––) indicate coaxial and optical digital audio connections. Choose either type  
(but not both) for each digital audio source.  
REC/IN  
Dotted lines (•••) indicate component, composite or S-video connections. Component video is  
the preferred connection when available, but you may use any of the three types (but not more  
than one). When component, composite and S-video sources are connected to the AVR, you must  
also connect all outputs from the AVR to your TV.  
PLAY/OUT  
Device Connection Options: Recommended connections are shown in red, but connections may be made to best fit your system requirements. The Video 4 inputs are on the front panel of the receiver.  
Device  
CD Player  
VCR  
Input Name Audio Input Connections  
Audio Output Connections  
Not required  
Video Connections  
CD  
CD L/R Inputs, Optical Digital 1 or 2, or Coaxial Digital 1 or 2  
Not required  
Video 1  
Video 1 L/R Inputs  
Video 1 L/R Outputs  
Not required  
Video 1 Composite or S-Video Input and Output  
Video 2 or 3 Composite or S-Video or Component Video Input  
Cable Box or Satellite Receiver Video 2 or 3  
Video 2 or 3 L/R Inputs, Optical Digital 1 or 2, or Coaxial Digital 1 or 2 Inputs*  
Tape L/R Inputs, Optical Digital 1/2** or Coaxial Digital 1/2** Inputs  
Audio Recorder  
Tape  
Tape L/R Outputs, Digital Optical** or Coaxial Outputs** Not required  
Not required Monitor-Out Composite and/or S-Video and/or Component  
TV or Video Display  
Not applicable Not required  
Check with your cable company to determine whether digital audio is available for all channels. It may be necessary to make BOTH analog and digital connections if it is not.  
Digital audio recorders only.  
*
**  
®
SOURCE COMPONENT CONNECTIONS  
 

Graco Heat Pump 3A2889A User Manual
Graco Inc Paint Sprayer 225877 User Manual
Graco Pressure Washer 3A0465C User Manual
Graco Stroller ISPC090BB User Manual
Harbor Freight Tools Bicycle Accessories 66552 User Manual
Hasbro Games 05068 User Manual
Hasbro Motorized Toy Car 17345 User Manual
Hoshizaki Freezer HNC 120AA L R User Manual
Hoshizaki Ice Maker KM 1300SAH E User Manual
HP Hewlett Packard Grinder LSG202A User Manual