Hotpoint Ventilation Hood LI2SZA User Manual

Instructions for Installation and Use  
Electric Hood  
 
Installation  
Preliminary information for installation of the hood:  
Disconnect the hood during electrical connection, by  
turning the home mains switch off.  
Expansion wall plugs are provided to secure the hood  
to most types of walls/ceilings. However, a qualified  
technician must verify suitability of the materials in  
accordance with the type of wall/ceiling. The  
wall/ceiling must be strong enough to take the weight  
of the hood.  
! It is important to conserve this booklet for  
consultation at any moment. In the case of sale,  
cession or move, make sure it is together with the  
product.  
UK  
! Read the instructions carefully: there is important  
information about installation, use and safety.  
! Do not carry out electrical or mechanical variations  
on the product or on the discharge conduits.  
Do not tile, grout or silicone this appliance to the wall.  
Surface mounting only.  
Do not fix chimney flue to furniture or fly over shelves  
unless the chimney flue can be easily removed, in  
case maintenance is ever required.  
Where foreseen remove the grease collecting panels.  
Remove the grease filter/s  
Do not tile, grout or silicone this appliance to the wall.  
Surface mounting only.  
Do not fix chimney flue to furniture or fly over shelves  
unless the chimney flue can be easily removed, in case  
maintenance is ever required.  
Installation  
Electric connection  
! The power tension must correspond with the tension  
shown on the characteristics label situated inside the  
hood. If provided with a plug, attach the hood to a  
socket conforming to the regulations in force and  
placed in an accessible zone. If without a plug,  
(connected directly to the power supply), use a  
regulation bipolar switch with a distance of the  
contacts on opening not less than 3mm (accessible).  
Assembling the chimney flue support/bracket (3 parts):  
The three parts should be fixed with 4 screws, the  
support extension is adjustable and should correspond  
to the internal width of the telescopic chimney flue.  
! If necessary, the situating of the supply cable must  
be carried out by the technical assistance service or a  
qualified person.  
Assembling the deflector (only when  
a
deflector  
composed of 3 parts is supplied – the deflector should  
be only for the filter version):  
The three parts should be fixed with 2 screws, the  
deflector extension is adjustable and should  
correspond to the width of the chimney flue support, to  
which it is then fixed.  
! An authorized installer must carry out the electrical  
connection of the hood.  
! The company declines any responsibility whenever  
these regulations are not respected.  
X
=
=
G
F
=
X
=
X
G
F
H
The minimum distance between the supporting surface  
for the cooking vessels on the hob and the lowest part  
of the range hood must be not less than 50cm from  
electric cookers and 65 cm from gas or mixed cookers.  
If the instructions for installation for the gas hob specify  
a greater distance, this must be adhered to.  
1.Draw a line corresponding to the centre line on the  
 
wall to the ceiling with  
installation operations.  
a
pencil. It will help the  
collecting panels) and check the perfect functioning of  
the hood.  
K
2.Apply the perforation diagram to the wall: The centre  
vertical line printed on the perforation diagram must  
correspond to the centre line drawn on the wall. In  
addition, the lower edge of the perforation diagram  
must correspond to the lower edge of the hood:  
keeping mind that the lower part of the hood, once  
installation is completed, must distance at least 50 cm  
from the cooking surface in case of electric plates and  
65 cm in case of gas rings or mixed tops.  
G
=
=
X
F
X
H
3.Place the support bracket on the perforation diagram  
making it coincide with the rectangle marked out. Mark  
the two external holes and make the holes. Remove the  
peroration diagram, insert two wall dowels and fix the  
support bracket of the hood with two 5x45mm screws.  
4.Hang up the suction unit.  
18a  
18a  
H
5.Adjust the distance of the suction unit from the wall.  
6.Adjust the horizontal setting of the suction unit.  
7. Mark the hole for definitively fixing the suction unit  
from inside the suction unit with a pencil.  
11  
11  
18b  
G
12  
18b  
8.Remove the suction unit from the bracket.  
9.Make a hole at the marked point (Ø8mm - see  
operation 7).  
4-13  
19  
1
4-13  
8
8
16  
10.Insert 1 wall dowel.  
17  
3
11.Apply flue support bracket „G“ to the ceiling, using  
the support bracket as a perforation diagram (the small  
slot on the support must coincide with the line  
previously traced on the wall – operation 1) and mark 2  
holes with the pencil. Make the holes (Ø8mm) and  
insert 2 dowels.  
2
B
9
5
6
5
6
10  
7
14  
12.Fix the flue support bracket to the wall with two  
5x45mm screws.  
13.Connect the suction group to the lower bracket.  
14. Definitively fix the suction unit to the wall  
(COMPULSORY!!).  
15  
15  
15  
15  
15.Position the hood on the suction unit (insert it  
partially), connect the electricity, fix the hood to the  
suction unit (from inside with 3 screws at the sides and  
2 in front) after having completely inserted it into its  
housing.  
16.Connect the tube (tube and band for fixing not  
supplied and must be purchased) for discharging the  
fumes at the connection ring placed over the suction  
motor unit.  
The other end of the tube must be connected to a  
fumes expulsion device towards the outside in the  
case of using a suction version hood. If you want to  
use a filtering hood, fix baffle F to flue support staff G  
and connect the other end of the tube to the  
connection ring placed on baffle F.  
17.Connect the electricity.  
18.Apply the flues and fix them with 2 screws (18a) to  
flues support „G“ (18b).  
19.Let the lower part of the flue slide to completely  
cover the suction unit until it is inserted into the  
apposite housing over the hood.  
Mount the fats filter/s (and where envisaged, the fat  
 
Description of the appliance  
Control panel  
Calibrating the control panel  
When the plug is inserted (or after a blackout) the  
system calibrates the keys; during calibration the  
display point flashes. Calibration lasts 15”. The point  
stops flashing at the end of calibration.  
Fats filter signal: this symbol (red led) lights up  
after 40 hours. Reset the signal by pressing for a  
long time (at least 3 seconds) until the beep confirms  
it.  
Off/Stand by: the On condition is obtained by  
pressing  
and  
for 3 seconds; in this case keys  
Carbon filter signal action.  
This signal is shown only if it has been previously set.  
Proceed as follows: press  
with the hood in Off:  
are enabled, the display point and the blue led  
of the relative keys light up. The Off condition is  
first  
turns red, after about 1 second  
also  
turns red. If you want to eliminate the carbon filter  
obtained by pressing  
again for 3 seconds.  
signal previously set, press  
with the hood in Off.  
Reset the carbon filter signal (after 160 hours) by  
On/Off lights: press  
to switch on the lights,  
which turn amber. Contemporaneously the symbols at  
the sides and turn blue: the intensity of  
pressing  
the beep).  
for a long time (about 3 seconds, until  
the light can be increased and diminished with these.  
Once the luminosity has been set, pressing  
rapidly again memorises it (the symbol turns blue) and  
the light  
switches off.  
On/Off motor: press  
to switch the motor on.  
It turns amber. Contemporaneously the symbols at the  
sides  
Press  
and  
or  
as well as  
turn blue.  
to adjust the intensity of  
suction. Pressing  
again switches the motor off  
and the last speed set is memorised.  
Intensive timing: by pressing this key the suction  
of the hood becomes intensive for a maximum time of 5  
minutes. At the end the hood returns to the speed  
previously set. To exit from the function earlier press  
or one of the following keys:  
.
,
or  
 
Operation  
! We advise switching the hood on, at minimum power,  
before beginning to cook to favour the optimal  
expulsion of odours. In addition we advise turning it off  
every time 10/15 minutes after finishing cooking.  
! We advise frying under the hood only under constant  
supervision.  
! It is forbidden to cook flambé under the hood  
because there is the risk of causing a fire.  
The best performance of the apparatus is obtained  
with external expulsion: we advise using the hood in  
this version if possible.  
External exhausting version  
In this case the fumes are conveyed outside by means  
of a special pipe connected with the connection ring  
located on top of the hood Diameter of the exhausting  
pipe must be equal to that of the connection ring =  
150mm.  
In the horizontal runs the exhausting pipe must be  
slightly slanted (about 10°) and directed upwards to  
vent the air easily from the room to the outside.  
Attention! If the hood is supplied with active charcoal  
filter, then it must be removed.  
Filtering version  
One active charcoal filter is needed for this and can be  
obtained from your usual retailer.  
The filter removes the grease and smells from the  
extracted air before sending it back into the room  
through the upper outlet grid.  
 
Maintenance  
! It is always necessary to isolate the hood from the  
power supply during cleaning and maintenance.  
Therefore remove the plug.  
UK  
We recommend carrying our maintenance regularly  
(about every 10 days) to ensure efficacious and  
constant performance of the hood.  
Cleaning the hood  
The hood should be cleaned frequently, both internally  
and externally. Use  
detergent liquids.  
a
cloth damped in neutral  
Avoid the use of products containing abrasives.  
Attention: failure to observe the cleaning regulations of  
the hood and the substitution and cleaning of the filters  
leads to the risk of fire. We therefore recommend  
keeping to the suggested instructions.  
Cleaning the grease filters  
The fats filter serves to capture the particles of fat in  
suspension that come from the cooking.  
It must be cleaned once a month with non-aggressive  
detergents manually or in  
temperature and short cycle.  
a
dishwasher at low  
If washed in a dishwasher it can become opaque over  
time but its filtering ability is not lessened in any way.  
Dismantle it using the corresponding handles, pushing  
them backward first and then pulling them down.  
After having washed it, dry it carefully and assemble it  
again in its seat, reversing the procedure.  
Clean the perimeter suction panel (when envisaged)  
with the same frequency as the anti-fat filter. Use a  
cloth and a not too concentrated liquid detergent.  
Never use abrasive substances.  
Carbon filter  
Remove the filter holder frame by turning the knobs (g)  
90° that affix the chimney to the cooker hood.  
Insert the pad (i) of activated carbon into the frame (h)  
and fit the whole back into its housing (j).  
Cleaning the carbon filter  
j
The charcoal filter can be washed once every two  
months using hot water and a suitable detergent, or in  
a dish-washer at 65°C (if the dish-washer is used,  
select the full cycle function and leave dishes out).  
Eliminate excess water without damaging the filter,  
then remove the mattress located inside the plastic  
frame and put it in the oven for 10 minutes at 100° C to  
dry completely. Replace the mattress every 3 years  
and when the cloth is damaged.  
i
g
g
h
Mounting and changing the filter  
To remove the panels pull them back (the support pins  
will disconnect from the housing).  
Pull the spring disconnection handle to dismantle the  
fats filter.  
 
Replacing lamps  
Remove the  
plug!  
Bulb/s:  
Remove the  
overhead light  
and remove  
the bulb to  
change. Only  
use 40W  
lamps.  
Make sure the  
bulbs are cold  
before  
touching  
them.  
Halogen bulbs:  
Use a small screwdriver or other tool suitable for  
prising.  
Substitute the halogen bulb with another of equal  
value. Close with the trigger fixing.  
 
Caution  
Disused domestic appliances can be delivered to  
the public collecting service, taken to suitable local  
authority areas or, if envisaged by national laws on the  
matter, resold to dealers at the same time as  
General safety  
! The hood has been designed and constructed in  
conformity with international safety regulations. These  
warnings are provided for safety reasons and must be  
carefully read.  
This apparatus has been designed for use by adults.  
Children and invalids are not allowed to use this  
apparatus without supervision. Check that children do  
not play with the apparatus.  
The premises must have sufficient ventilation when  
the hood is being used at the same time as other  
apparatuses that use gas and other fuels. If the hood  
must be installed in a kitchen where there is a water-  
heater or a gas heating system we recommend, for  
safety reasons, not using the suction version. It is  
therefore necessary to equip the apparatus with an  
active carbon filter, in this way allowing recycling use.  
For safe performance, low pressure should not  
exceed 0.04 mbar: in this way re-suction of the  
expulsion gas will be avoided. This can be obtained  
ensuring entry of air into the room through openings  
that cannot be closed.  
The sucked air must not be conveyed in a conduit  
used for the discharge of fumes from apparatuses  
supplied with energy other than electricity.  
It is severely forbidden to cook food on the flame  
under the hood.  
The use of naked flame damages the filters and can  
cause fires. It must therefore be avoided in any case.  
Frying must be carried out under control to avoid the  
overheated oil catching fire.  
As far as the technical and safety measures to adopt  
for the discharge of fumes are concerned, keep strictly  
to what is envisaged by the regulations of the  
competent authorities.  
purchasing new, equivalent, types of product.  
All the main producers of domestic appliances are  
active in the creation and management of collecting  
systems of disused apparatuses.  
! In case of anomalies apply to the authorized technical  
assistance service and require original spare parts.  
! The information and technical data are subject to  
change and the producer, in line with technical  
progress, maintains the right to make modifications  
that he considers necessary without prior notice.  
This appliance is marked according to the European  
directive 2002/96/EC on Waste Electrical and  
Electronic Equipment (WEEE). By ensuring this product  
is disposed of correctly, you will help prevent potential  
negative consequences for the environment and  
human health, which could otherwise be caused by  
inappropriate waste handling of this product.  
The symbol  
on the product, or on the documents  
accompanying the product, indicates that this  
appliance may not be treated as household waste.  
Instead it shall be handed over to the applicable  
collection point for the recycling of electrical and  
electronic equipment. Disposal must be carried out in  
accordance with local environmental regulations for  
waste disposal.  
For more detailed information about treatment,  
recovery and recycling of this product, please contact  
your local city office, your household waste disposal  
service or the shop where you purchased the product.  
For any problem regarding the expulsion of fumes,  
keep to the instructions of the competent authority.  
The company declines any responsibility in the case of  
damage or fire caused by apparatus resulting from  
failure to observe the above-mentioned instructions.  
Disposal  
Disposing of the packaging material: keep to the  
local regulations so that the packaging can be re-used.  
European directive 2002/96/CE on electric and  
electronic apparatus waste provides that domestic  
appliance should not be disposed of in the normal flow  
of solid urban waste. The disused apparatuses must  
be collected separately to make the rate of recovering  
and recycling of the materials they consist of and  
prevent potential damage to health and the  
environment. The symbol of the barred basket is shown  
on all the products to remind users of the need for  
separate collection.  
 
 
After Sales Service  
"No company is better positioned to offer an after sales service on a  
Hotpoint appliance than us - the manufacturer"  
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive  
parts and labour guarantee for the first 12 months. In addition to this you also have the advantage of  
free replacement parts for the first 5 years when fitted by a Hotpoint  
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales  
service options:  
Repair Service and Information Help Desk  
UK: 08709 066066  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the Model number and the Serial number of your appliance  
Available 364 days a year with a fast, effective and value for money service. We have the largest  
white goods repair service in the UK with over 1000 of our own fully trained engineers. All repairs  
include a parts and labour guarantee for 12 months from the date of the repair.  
If you require any information or have any questions about your appliance, our operators are on hand  
with help and advice.  
All this ensures that you will receive the best available after sales service possible.  
Extended Warranties  
UK: 08709 088 088  
Republic of Ireland: 1850 502 200  
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service  
cover plans to give you total peace of mind.  
Repair Protection Plan  
-
FREE service repairs for a single Hotpoint appliance during the  
period of cover.  
FREE service repairs for all your Hotpoint appliances less than  
Kitchen Cover  
-
8 years old.  
Genuine Parts and Accessories  
UK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
A wide range of genuine parts and accessories are available from our hotline or through our website.  
Genuine parts and accessories, extended warranties and service repairs are all  
available on our web-site at:  
GB910  
 
Key Contacts  
After Sales Service  
Over 1200 trained specialists, directly employed by us, ensure that you can have complete  
confidence in both the appliances and services we offer.  
Repair Service and Information Desk  
UK: 08709 066 066  
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Model number:  
Serial number:  
Extended Warranties  
UK: 08709 088 088  
(Open 8 to 8 Mon - Sun)  
Republic of Ireland: 1850 502 200  
Genuine Parts and Accessories  
UK: 08709 077 077  
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)  
Republic of Ireland: (01) 842 6836  
Indesit Company, Morley Way , Peterborough, PE2 9JB  
LI2SZA Ed. 01/06  
 

Graco Inc Marine Instruments 218 600 User Manual
HANNspree Flat Panel Television ST57 12U1 User Manual
Harman Kardon CD Player HD710 User Manual
Hearth and Home Technologies Indoor Fireplace COLBAY INS User Manual
Honeywell Thermostat AQ1000TP2 User Manual
HP Hewlett Packard Laptop 376311 001 User Manual
Hunter Fan Ventilation Hood 81003 User Manual
Husqvarna Welding Consumables YTH2242TDRF User Manual
Hypertec Mouse KYBAC595 USBWHTHY User Manual
Hy Tek Manufacturing Flat Panel Television Tek Panel 570 User Manual